06 ATTACHMENTS - Laserfiche WebLink

Blocked e 4/16"' Blocked'` 4/12 Blocked e 8/12 - Blocked a 6/12 a 7 6d cooler (1 x 0.092 ") or Unblocked 4 Wallboard 0.120" narl, min. 3 /8" 7 -- head, 13/4' long No 16 gage galv. staple, 1 - Blocked e — 4 legs, 1 long Base ply -6d cooler (1 - x 0.092 ") or wallboard 1 x 0.120" nail, min. 3/e' head 1- 5/ 16 gage galv. Staple 1- /8 16 Blocked a Base ply: 9 gage galv. staple Two -ply Face ply: 7 3 Face ply -8d cooler (2- /8 x 0.113 ") or wallboard 0.120" nail, min. 3 /8 ' head, 2 - long No. 15 gage galv. staple, 2 -'/4" long _ Unblocked 8/12 c Blocked e 8/12 " No. 6-1-Y4" screws For 51. 1 inch = 25 4 mm, 1 fool = 304 8 mm, 1 pound per fool = 14.5939 N /m a Applies to fastening at studs, top and bottom plates and blocking. b Alternate fasteners are permitted to be used if their dimensions are not less than the specified dimensions. Drywall screws are permitted to substitute for the 5d 1 -5 /8 x 00861, and 6d (1 -7/8' x 0.092 ")(cooler) nails listed above, and No. 6 1-1/4", inch Type S or W screws for 6d (1 -7/8' x 0 092') (cooler) nails c. For properties of cooler nails, see ASTM C 514 d . Maximum framing spacing of 24 inches on center e All edges are blocked, and edge fastening is provided at all supports and all panel edges f. First number denotes fastener spacing at the edges, second number denotes fastener spacing at intermediate framing members g. Screws are Type W or S h. Staples shall have a minimum crown width of 7/16 inch, measured outside the legs. and shall be installed with their crowns parallel to the long dimension of the framing members 1. Staples for the attachment of gypsum lath and woven -wire lath shall have a minimum crown width of 3/4 inch, measured outside the legs. 20.08.140 CBC Section 2308.12.4 amended — Braced wall line sheathing. Section 2308.12.4 is amended to read as follows: 2308.12.4 Braced wall line sheathing. Braced wall lines shall be braced by one of the types of sheathing prescribed by Table 2308.12.4 as shown in Figure 2308.9.3. The sum of lengths of braced wall panels at each braced wall line shall conform to Table 2308.12.4. Braced wall panels shall be distributed along the length of the braced wall line and start at not more than 8 feet (2438mm) from each end of the braced wall line. Panel sheathing joints shall occur over studs or blocking. Sheathing shall be fastened to studs, top and bottom plates and at panel edges occurring over blocking. Wall framing to which sheathing used for bracing is applied shall be nominal 2 inch wide [1'/2 inch (38 mm)1 or large members. Braced wall panel construction types shall not be mixed within a braced wall line. Braced wall panels required by Section 2308.12.4 may be eliminated when all of the following requirements are met: 1. For one story detached garage Group U occupancies not more than 25 feet in depth or length. 37