04 - Laserfiche WebLink

0721609 Controller, Pressure, Pierce LCD, Custom Chassis PIERCE PRESSURE CONTROLLER A Pierce electronic pressure controller will be provided. A pressure transducer will be installed in the discharge side of the water pump. The transducer continuously monitors pump pressure sending a signal to the electronic pressure controller. The pressure controller can be used in two (2) modes of operation, RPM mode and pressure modes. The controller will be programmed to turn on/default to No Mode/Default Press Setting mode. In the RPM mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will maintain the set engine speed, regardless of engine load (within engine operation capabilities). In the pressure mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will automatically maintain the discharge pressure set by the operator (within the discharge capabilities of the pump and water supply) regardless of flow. A 2.00" diameter throttle control knob with no mechanical stops, a serrated grip, and a red idle push button in the center will be a integrated/part of the pressure controller. The throttle control knob will be programmed for Clockwise rotation to increase engine speed. Individual LED indicators for ok to pump, throttle ready, pressure mode and rpm mode will be located on the pressure controller for easy viewing. A pump cavitation protection feature will also provided which will return the engine to idle should the pump cavitate. Cavitation is sensed by the combination of pump pressure below 30 psi and engine speed above 2000 rpm for more than five (5) seconds. Other safety features include recognition of low water and no water conditions with an automatic programmed response and a push button to return the engine to idle. The pressure controller LCD screen will be 4.20" in size with a minimum brightness of 750 nits. The LCD screen and LED intensity will be automatically adjust for day and nighttime operation. The LCD screen intensity can also be manually adjusted if needed. The following information will be provided/displayed on the LCD screen - Engine RPM Check engine and stop engine warning indicators Engine oil pressure Engine coolant temperature Water pump transmission temperature Fuel Level Water tank level Battery voltage Operating mode (RPM or pressure) Pressure or RPM setting On screen messaging show diagnostic and warning messages as they occur. It will show apparatus information, stored data, and program options when selected by the operator. It will monitor inputs outputs and support audible and visual warning alarms for the following conditions - High battery voltage Low battery voltage/engine off Low battery voltage/engine running High water pump temperature Low fuel Low engine oil pressure High engine coolant temperature Water tank out of water (visual alarm only) No engine response (visual alarm only) The pressure controller will store the accumulated operating hours for the pump and engine. These items are to be displayed within the pressure controller menu. The pressure controller will include a USB port on the back of the controller for easy software upgrades if needed. 0641743 Primer, Waterous, VPO Motor, (1) VAP Valve, (1) Push Button Control PRIMER SYSTEM A Waterous electric pump priming system conforming to standards outlined in the current edition of NFPA 1901 will be furnished with the apparatus. One (1) VPO electric motor driven rotary vane primer will be provided. One (1) VAP vacuum activated priming valve will be plumbed main pump. One (1) momentary push-button control will be located at the pump operator's panel. The push button control system control will operate an electric priming motor and the priming valve will automatically open during priming and close when the primer is deactivated. 0044552 Line, 0.50" Recirculating w/Check Valve RECIRCULATING LINE WITH CHECK VALVE A 0.50" diameter recirculating line, from the pump to the water tank, will be furnished with a control installed at the pump operator's control panel. A check valve will be provided in this line to prevent the back flow of water from the tank to the pump if the valve is left in the open position. 0604521 SP Foam/Pump Drains, Location PUMP DRAIN LOCATION The foam/pump drains will be located as high and as far inboard as possible. 0780364 Manuals, Pump, (2) Total, Electronic Copies PUMP MANUALS There will be a total of two (2) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two (2) electronic copies. Each manual will cover pump operation, maintenance, and parts. 47717Bid #: