04 - Laserfiche WebLink

0603128 Plumbing, Stainless Steel and Hose, Two Stage Pump PLUMBING, STAINLESS STEEL AND HOSE All inlet and outlet lines will be plumbed with either stainless steel pipe, hydraulic type hose or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule 10 wall thickness. Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings. Plumbing manifold bodies will be ductile cast iron or stainless steel. All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame. All water carrying gauge lines will be flexible polypropylene tubing. All piping, hose and fittings will have a minimum of a 700 PSI hydrodynamic pressure rating. 0795135 Plumbing, Stainless Steel, w/Foam System FOAM SYSTEM PLUMBING All piping that is in contact with the foam concentrate or foam/water solution will be stainless steel. The fittings will be stainless steel or brass. Cast iron pump manifolds will be allowed. 0004645 Inlets, 6.00" - 1250 GPM or Larger Pump MAIN PUMP INLETS A 6.00" pump manifold inlet will be provided on each side of the vehicle. The suction inlets will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump. 0014650 Pump Suction Tube(s), Short, All SHORT SUCTION TUBE(S) The suction tube(s) on the water pump will have short suction tube(s) installed to allow for installation of adapters, elbows or intake valves without excessive overhang. 0004646 Cap, Main Pump Inlet, Long Handle, NST, VLH MAIN PUMP INLET CAP The main pump inlets will have National Standard Threads with a long handle chrome cap. The cap will be the Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected. 0084610 Valves, Akron 8000 series- All VALVES All ball valves will be Akron® Brass. The Akron valves will be the 8000 series heavy-duty style with a stainless steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve. Valves will have a ten (10) year warranty. 0004686 Valve, Inlet(s) Recess Behind Panel, Side Cntrl The location of the valve for the two (2) inlets will be behind the pump panel. 0004700 Control, Inlet, at Valve INLET CONTROL The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve. 0004660 Inlet (1), Left Side, 2.50" LEFT SIDE INLET There will be one (1) auxiliary inlet with a 2.50" valve at the left side pump panel, terminating with a 2.50" (F) National Standard hose thread adapter. The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0004680 Inlet, Right Side, 2.50" RIGHT SIDE INLET There will be one (1) auxiliary inlet with a 2.50" valve at the right side pump panel, terminating with a 2.50" (F) National Standard hose thread adapter. The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0034720 Anode, Zinc, Pair, Pump Inlets ANODE, INLET A pair of sacrificial zinc anodes will be provided in the water pump inlets to protect the pump from corrosion. 0092569 No Rear Inlet (Large Dia) Requested 0064116 No Rear Inlet Actuation Required 0092696 Not Required, Cap, Rear Inlet 0009648 No Rear Intake Relief Valve Required on Rear Inlet 48717Bid #: