04 - Laserfiche WebLink

0775183 SP Outlet, 4" w/4" Right, Small Handwheel LARGE DIAMETER DISCHARGE OUTLET There will be a 4.00" discharge outlet with a 4.00" Akron valve installed on the right side of the apparatus, terminating with a 4.00" (M) National Standard hose thread adapter. This discharge outlet will be actuated with a small handwheel control at the pump operator's control panel. An indicator will be provided to show when the valve is in the closed position. 0005097 Elbow, Large Dia Outlet, 30 Deg, 4.00" FNST x 5.00" Storz LARGE DIAMETER OUTLET ELBOWS The 4.00" outlet(s) will be furnished with one (1) 4.00" (F) National Standard hose thread x 5.00" Storz elbow adapter with Storz cap. 0649939 Outlet, Front, 1.50" w/2" Plumbing FRONT DISCHARGE OUTLET There will be one (1) 1.50" discharge outlet piped to the front of the apparatus and located on the top of the left side of the front bumper. Plumbing will consist of 2.00" piping and flexible hose with a 2.00" ball valve with control at the pump operator's panel. A fabricated weldment made of stainless steel pipe will be used in the plumbing where appropriate. The piping will terminate with a 1.50" NST with 90 degree stainless steel swivel. There will be automatic drains provided at all low points of the piping. 0092575 Not Required, Outlet, Rear 0045099 Not Required, Elbow, Rear Outlets 0092574 Not Required, Outlet, Rear, Additional 0085695 Not Required, Elbow, Rear Outlets, Large, Additional 0000216 Outlets, (3) Front HB, (2) 1.50" (1) 2.50" FRONT OF HOSE BED DISCHARGE OUTLET There will be three (3) discharges located at the front of the hose bed, both 1.50" outlets to be on the driver side in bay #1 and #2 and the 2.50" outlet shall be on the bay #5, please locate 4.00" inboard of the P/S side sheet/divider. Match 29597. Plumbing for the 2.50" outlet will consist of 2.50" piping with a 2.50" full-flow ball valve and plumbing to the 1.50" outlets will consist of 2.00" piping and 2.00" full-flow ball valves. All three (3) outlets will be controlled at the pump operator's panel. The discharges will terminate with a one (1) 2.50" and two (2) 1.50" (M) National Standard hose thread adapter. 0752078 Caps/Plugs for 1.00" to 3.00" Discharges/Inlets, S/S Cable DISCHARGECAPS/ INLET PLUGS Chrome plated, rocker lug, caps with S/S cables will be furnished for all discharge outlets 1.00" thru 3.00" in size, besides the pre-connected hose outlets. Chrome plated, rocker lug, plugs with S/S cables will be furnished for all auxiliary inlets 1.00" thru 3.00" in size. The caps and plugs will incorporate a thread design to automatically relieve stored pressure in the line when disconnected. 0723042 Valve, 0.75" Bleeder, Discharges, "T" Swing Handle OUTLET BLEEDER VALVE A 0.75" bleeder valve will be provided for each outlet 1.50" or larger. Automatic drain valves are acceptable with some outlets if deemed appropriate with the application. The valves will be located behind the panel with a T swing style handle control extended to the outside of the side pump panel. The handles will be chrome plated and provide a visual indication of valve position. The T swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage. Bleeders will be located at the bottom of the pump panel. They will be properly labeled identifying the discharge they are plumbed in to. The water discharged by the bleeders will be routed below the chassis frame rails. 0090926 Outlet, 3.00" Deluge w/TFT Extend-a- Gun XG12 DELUGE RISER A 3.00" deluge riser will be installed above the pump in such a manner that a monitor can be mounted and used effectively. Piping will be rigidly braced and installed securely so no movement develops when the line is charged. The riser will be gated and controlled at the pump operator's panel. Any 3.00 inch or larger discharge valve will be a slow-operating valve in accordance with NFPA 16.7.5.3. TELESCOPIC PIPING The deluge riser piping will include a 12.00" Task Force Model XG12 Extend-A-Gun extension. This extension will be telescopic to allow the deluge gun to be raised 12.00" increasing the range of operation. A position sensor will be provided on the telescopic piping that will activate the "do not move vehicle" light inside the cab when the monitor is in the raised position. 50717Bid #: