04 - Laserfiche WebLink

0752655 SP Monitor, TFT Crossfire XFC-52, 5" Storz Inlet, 5" Shaper, Package MONITOR A Task Force Crossfire XFC-52 monitor package will be furnished and properly installed on the deluge riser. The monitor will include a 1250 GPM automatic M-R nozzle, 5.00" stream straightener and quad stacked tips. Also provided will be a portable base unit with one (1) 5.00" Storz inlet. The monitor will be painted as provided by monitor manufacturer. 0047175 No Additional Nozzle Req'd 0046857 Deluge Mount, For TFT Crossfire Monitor, TFT Manual Extend-A-Gun Only The deluge riser Extend-a-Gun will have provisions for direct mounting a Task Force Tips CrossFire monitor. 0723726 Speedlay Module Not Required 0722432 Hose Restraint Not Required, No Speedlay Module 0723395 Speedlays, Not Required 0723394 Speedlays, Not Required 0029210 Crosslays Sngl Sheet, (2+) 1.50", Spl. Cap/Arrangement CROSSLAY HOSE BEDS, 1.50" Two (2) crosslays with 1.50" outlets will be provided. Each bed to be capable of carrying both at 200' of 1.75" DJ Hose and will be plumbed with 2.00" i.d. pipe and gated with a 2.00" quarter turn ball valve. Outlets to be equipped with a 1.50" National Standard hose thread 90 degree swivel located in the hose bed so that hose may be removed from either side of apparatus. The crosslay controls will be at the pump operator's panel. The center crosslay dividers will be fabricated of .25" aluminum and will provide adjustment from side to side. The divider will be unpainted with a brushed finish. Vertical scuffplates, constructed of stainless steel, will be provided at the front and rear ends of the bed on each side of vehicle. Crosslay bed flooring will consist of removable perforated brushed aluminum. 0092183 Deadlay(s) No Plumbing, Spl Capacity, DEADLAY HOSE BEDS One (1) deadlay bed, without plumbing, will be provided above the pump compartment capable of carrying please match the size of the two crosslays, make the deadlay 7.50" wide. The center crosslay dividers will be fabricated of .25" aluminum and will provide adjustment from side to side. The divider will be unpainted with a DA finish. The remainder of the crosslay bed will be painted job color. Stainless steel vertical scuffplates will be provided at hose bed ends (each side of vehicle). Bottom of hose bed ends (each side) will also be equipped with a stainless steel scuffplate. Deadlay bed flooring will consist of removable perforated brushed aluminum. 0601568 SP Hose Restraint, Crosslay/Deadlay, Vinyl, Seatbelt, Each Side, Ends CROSSLAY/DEADLAY HOSE RESTRAINT There will be black vinyl end flap provided across each end of three (3) crosslay/deadlay opening (s) to secure the hose during travel. Each vinyl end flap will be permanently attached at the top of the crosslay/deadlay opening(s). They will be attached with seatbelt fasteners. 3.00" long male seat belt anchors will be provided for use with the seat belt webbing. The anchors will be provided with footman style loops at the bottom of the crosslay opening. 0029260 Not Required, Speedlays 0750536 Hose Restr, Spdly, Not Required, No Spdly 0580925 Hose Restraint, Crosslay/Deadlay, 3/16" Alum Treadplate, Top Only CROSSLAY/DEADLAY HOSE RESTRAINT A hinged .19" aluminum treadplate cover, hinged at the front will be installed over the crosslay/deadlay(s). It will include a latch at each end of the cover to hold it securely in place, a chrome grab handle at each end for opening and closing the cover and a foam rubber gasket where the cover comes into contact to a painted surface. The cover will be provided with rubber latch hold open device. 0076048 SP Crosslays, 11.00" Lower Than Standard CROSSLAY 11.00" LOWER THAN STD The crosslays will be lowered 11.00" from standard. 51717Bid #: