|
0750526 Gauge, Water Level, Pierce, In
<br />pressure Controller, Lt Driver
<br />
<br />WATER LEVEL GAUGE
<br />An electric water level gauge will be incorporated in the pressure controller that registers water
<br />level by means of 9 LEDs. They will be at 1/8 level increments with a tank empty LED. The LEDs
<br />will be a bright type that is readable in sunlight, and have a full 180-degree of clear viewing.
<br />To further alert the pump operator, the gauge will have a warning flash when the tank volume is
<br />less than 25%, and will have "Down Chasing LEDs when the tank is almost empty.
<br />The level measurement will be ascertained by sensing the head pressure of the fluid in the tank
<br />or cell.
<br />There will be a light driver module with this installation to power additional water level gauge(s)
<br />included on the apparatus.
<br />0750438 Water Level Gauge, Wln PSTANK2,
<br />LED 1-Light, 4-Level
<br />WATER LEVEL GAUGE
<br />There will be two (2) additional water level indicator(s), Whelen®, Model PSTANK2, LED module
<br />with black trim, installed one (1) each side rearward of crew cab doors.
<br />This light module(s) will include four (4) colored levels, and function similar to the water level
<br />indicator located at the operators panel:
<br />First green module indicates a full water level
<br />Second blue module indicates a water level above 3/4 full
<br />Third amber module indicates a water level above 1/2 full
<br />Last red module indicates a water level above 1/4 full and empty
<br />Above 1/4 this light will be steady burning
<br />At empty this light will be flashing
<br />The flash rate will be determined by the main water level tank sensor.
<br />This module will be activated when the pump is in gear.
<br />0604354 Gauge, Foam Level, FRC, Tank
<br />Vision Pro, WLA 360-A00, Class "A"
<br />
<br />CLASS "A" FOAM LEVEL GAUGE
<br />A Fire Research TankVision Pro model WLA360-A00 cell/tank level indicator kit will be installed
<br />on the pump operators panel. The kit will include an electronic indicator module, a pressure
<br />sensor, a 10' sensor cable and a tank vent. The indicator will show the volume of Class "A" foam
<br />concentrate in the cell/tank on nine (9) easy to see super bright RGB LEDs. A wide view lens
<br />over the LEDs will provide for a viewing angle of 180 degrees. The indicator case will be
<br />waterproof, manufactured of Polycarbonate/Nylon material and have a distinctive green label.
<br />The program features will be accessed from the front of the indicator module. The program will
<br />support self-diagnostics capabilities, self-calibration, six (6) programmable colored light patterns
<br />to display cell/tank volume, adjustable brightness control levels and a data link to connect remote
<br />indicators. Low foam level warnings will include flashing LEDs at 1/4 cell/tank and down chasing
<br />LEDs when the cell/tank is almost empty.
<br />The indicator will receive an input signal from an electronic pressure sensor. The sensor will be
<br />mounted from the outside of the foam cell/tank near the bottom. No probe will be placed on the
<br />interior of the cell/tank. Wiring will be weather resistant and have automotive type plug-in
<br />connectors.
<br />0736304 SP Light Shield, S/S LED, 45 Deg Ends
<br />
<br />LIGHT SHIELD
<br />There will be a polished, 16 gauge stainless steel light shield with 45 degree end caps on both
<br />ends installed over the pump operator's panel.
<br />There will be 12 volt DC white LED lights installed under the stainless steel light shield to
<br />illuminate the controls, switches, essential instructions, gauges, and instruments necessary for
<br />the operation of the apparatus. These lights will be activated by the pump panel light switch.
<br />Additional lights will be included every 18.00" depending on the size of the pump house.
<br />One (1) pump panel light will come on when the pump is in ok to pump mode.
<br />There will be a light activated above the pump panel light switch when the parking brake is set.
<br />This is to afford the operator some illumination when first approaching the control panel.
<br />0736303 SP Light Shield, S/S, PS LED, 45 Deg
<br />Ends
<br />ADDITIONAL LIGHT SHIELD
<br />An additional polished, 16 gauge stainless steel light shield with 45 degree end caps on both
<br />ends provided above passenger's side pump panel.
<br />There will be 12 volt DC white LED lights installed under the light shield to illuminate the controls,
<br />switches, essential instructions, gauges, and instruments necessary for the operation of the
<br />apparatus. These lights will be activated by the pump panel light switch. Additional lights will be
<br />included every 18.00" depending on the size of the pump house.
<br />0606694 Air Horns, (2) Hadley, 6" Round,
<br />eTone, In Bumper
<br />AIR HORN SYSTEM
<br />Two (2) Hadley®, eTone, chrome air horns will be recessed in the front bumper. The air horn
<br />system will be piped to the air brake system wet tank utilizing 0.38" tubing. A pressure protection
<br />valve will be installed to prevent the loss of air in the brake system.
<br />0606834 Location, Air Horns, Bumper, Each
<br />Side, Outside Frame, Inboard (Pos
<br />#2 & #6)
<br />Air Horn Location
<br />The air horns will be located on each side of the bumper, just outside of the frame rails.
<br />0016065 Control, Air Horn, Horn Ring, PS
<br />Chrome Push Button
<br />
<br />Air Horn Control
<br />The air horns will be actuated by a chrome push button located on the officer's side of the engine
<br />tunnel and by the horn button in the steering wheel. The driver will have the option to control the
<br />air horns or the chassis horns from the horn button by means of a selector switch located on the
<br />instrument panel.
<br />55717Bid #:
|