04 - Laserfiche WebLink

0014329 Cutouts, (2) Handhold, Crosslay Divider CUTOUT, HANDHOLD, CROSSLAY DIVIDER Two (2) cutouts with radiused corners will be provided at side of the crosslay divider(s) two (2). 0664254 Shelf, Between Deadlay Divider HOSE BED SHELF A removable aluminum shelf will be installed in the deadlay hose bed located above the pump area. The shelf will be full width of the deadlay and will separate the deadlay into two (2) separate hose storage areas. 0015216 Reel, Booster, Aluminum - Over Pump, Right Side BOOSTER HOSE REEL A Hannay electric rewind booster hose reel will be installed over the pump in a recessed open compartment on the right side of the apparatus. The reel will be fabricated of aluminum and have highly polished end discs. A polished stainless steel roller and guide assembly will be mounted on the reel side of the apparatus. Discharge control will be provided at the pump operator's panel. Plumbing to the reel will consist of 1.50" Aeroquip hose and a 1.50" valve. 0683521 Switch, (2) Reel Rewind - Special Location Reel motor will be protected from overload with a sized automatic reset circuit breaker. Two (2) Electric rewind controls will be a rubber covered button installed on passenger side pump panel and in cargo area near reel. 0025262 SP Hose, Booster - 150' of 1.00"/800 PSI (100' + 50') 2-SECTIONS OF BOOSTER HOSE Booster hose, 1.00" diameter and 150 feet in length, with chrome plated Barway, or equal couplings will be provided. The hose will be coupled in two (2) sections. The first section will be 100' long and then a 50' section. Working pressure of the booster hose will be a minimum of 800 psi. 0017858 Capacity, Hose Reel 150' of 1" Capacity of the hose reel will be 150 feet of 1.00" booster hose. 0007428 Nozzle for Booster Reel Not Req'd 0515688 Gauge, Hose Reel, (Match Panel Gauges) PRESSURE GAUGE There will be a pressure gauge provided for one (1) hose reel(s). The gauge will be located near control on pump panel. The gauge will match the discharge outlet gauges. 0021954 Cutout for Reel Access, One, w/ S/S Trim HOSEREEL ACCESS A cutout will be provided in the side sheet next to the booster hose reel. This cutout will allow access to the hose and provide a window to view the reel. Stainless steel trim will be mounted horizontally and vertically around the cutout. 0046560 Manual, Override, Hose Reel A manual rewind will be provided for the booster hose reel. 0622237 Roller Assembly, Additional There will be one (1) additional polished stainless steel roller and guide assembly mounted driver side full width of the top of the cargo top flange. 0007293 Foam Sys, FoamPro 2001 (Single Agent) FOAM CONCENTRATE PROPORTIONING SYSTEM A Hypro FoamPro®, Model 2001, foam system will be provided as the means for the proportioning of foam concentrate into the water stream. The FoamPro is an electronic, fully automatic, variable speed, direct injection, discharge side foam proportioning system. This system will be capable of handling Class A foam concentrates, as well as most Class B foam concentrates. The foam system will be plumbed to six (6) discharges. The discharges capable of dispensing foam will be hose reel, front outlet, both crosslays, and both rear 1.50" HB outlets. The foam proportioning system operation will be based on a direct measurement of water flows, and remain consistent within the specified flow and pressure. The system will be equipped with a digital electronic control display on the pump panel. Incorporated within the control display will be a microprocessor, which receives input from the system flow meter while also monitoring the foam concentrate pump output. The microprocessor will compare the values of the water flow versus the foam flow, to ensure the proportion rate is accurate. One (1) paddle wheel will be installed to monitor all foam discharges. Push button control for the foam proportioning rate will allow a ratio from .1 percent to 3 percent in .1 percent increments. The rated capacity of this system will be 85 gpm at 3 percent and 500 gpm at .5 percent. A 2.5 gpm @150 psi, positive displacement foam pump will be powered by a 1/2 hp 12 vdc electric motor. One (1) check valve will be installed in the plumbing to prevent foam from contaminating the water pump. The check valve will be approved by the foam system manufacturer. 52717Bid #: